Hydraullic Units
50 mm Socket for 1 in. Square Drive
EP BSH1050
50 mm Socket for 1 in. Square Drive- Type: Torque Wrench Accessory
- Product Group: Torque Wrenches, Torque Wrench Pumps
- Product Line: Bolting Tools
- Series: BSH
- SubTypes: Socket - Metric
50 Ton (444, 8 Kn) Capacity, 10 in (254 mm ) Stroke, Double-Acting, Aluminum Center Hole Hydraulic Cylinder
EP RACD5010
50 ton (444,8 kN) Capacity, 10 in (254 mm) Stroke, Double-Acting, Aluminum Center Hole Hydraulic Cylinder- Technical coating reduces wear & corrosion.
- Steel piston for protection against load damage.
- Chrome plated sleeve for extra protection.
- Stop rings for piston blow-out protection.
- Rod wiper protects inner cylinder from dirt.
- Type: Hydraulic Cylinders
- Max Bar: 700
- Max PSI: 10000
- Product Line: Hydraulic Tools
- Series: RACD
- Stroke Inches: 10
- Stroke MM: 254
- SubTypes: Aluminum Center Hole Cylinder
- Capacity Imperial Tons: 50
- Capacity KN: 444,8
50 Ton (444, 8 Kn) Capacity, 2 in (50, 8 mm ) Stroke, Single-Acting, Aluminum Locknut Hydraulic Cylinder
EP RAL502
50 ton (444,8 kN) Capacity, 2 in (50,8 mm) Stroke, Single-Acting, Aluminum Locknut Hydraulic CylinderSimplex RAL Series Aluminum Hydraulic Cylinders feature lock nut that provide the reassurance of safe mechanical load holding for extended periods. These are approximately half the weight of steel equivalents and are expertly engineered to withstand tough applications in harsh conditions.
Aluminum is not only lighter, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. A carrying handle provided on all RAL cylinders also enhance portability.
Inside the cylinder is a high-strength return spring for plunger retraction and stop rings for protection against blow out. The cylinder exterior is finished with an anodized hard coat to extend cylinder life, and a wiper protects the inner cylinder assembly from dirt, moisture, and other contaminants.
- Type: Hydraulic Cylinders
- Max Bar: 700
- Max PSI: 10000
- Product Line: Hydraulic Tools
- Series: RAL
- Stroke Inches: 2
- Stroke MM: 50.8
- SubTypes: Aluminum Locknut Cylinder
- Capacity Imperial Tons: 50
- Capacity KN: 444,8
- Approximately half the weight of steel cylinders
- Lock nut for mechanical load holding for extended periods
- Heavy duty spring delivers fast and full retraction
- Hard anodized coating reduces wear and corrosion
- Stop rings prevent piston blow-out
- Wiper protects inner cylinder from dirt.
- Meets ANSI/ASME B30.1 Safety Standards
- Load tested under 125% of the nominal capacity
- For working pressures up to 10,000 psi (700 bar)
50 TON ALUM. CYLINDER, 250MM STROKE
EP RAC-5010
50 TON ALUM. CYLINDER, 250MM STROKE50 Ton Aluminum Cylinder, 6" Stroke
EP RAC-506
50 Ton Aluminum Cylinder, 6" Stroke50 TON HYD. CYLINDER W/13.13 STROKE
EP RR-5013
50 TON HYD. CYLINDER W/13.13 STROKE50 Ton, H-Frame Hydraulic Press with RR5013 Double-Acting Cylinder and ZA4408MX Air Pump
EP IPA5073
50 Ton, H-Frame Hydraulic Press with RR5013 Double-Acting Cylinder and ZA4408MX Air Pump- Type: Hydraulic Press
- Max Bar: 700
- Max PSI: 10000
- Product Group: Presses
- Product Line: Industrial Tools
- Series: IP
- SubTypes: H-Frame Press
- Capacity Imperial Tons: 50
- Capacity KN: 498
- Quality welded frame for maximum strength and long life
- Exclusive Hydra-Lift bed for effortless adjustment of the vertical daylight (10-ton models are manual)
- Roller head design is standard to allow movement and locking of the cylinder from side to side(10-ton, 25-ton, and 30-ton are manual)
- All models in the Quick Selection Chart have been matched to a pump, cylinder, hoses and gauge, offering the complete package
- Set Includes: RR5013, ZA4408MX, GF50P, HC9306, GA2
- Accessories: PK1002, A150, IPL100
50 Ton, H-Frame Hydraulic Press with RR5013 Double-Acting Cylinder and ZE4420SBN Electric Pump
EP IPE5060
50 Ton, H-Frame Hydraulic Press with RR5013 Double-Acting Cylinder and ZE4420SBN Electric Pump- Type: Hydraulic Press
- Max Bar: 700
- Max PSI: 10000
- Product Group: Presses
- Product Line: Industrial Tools
- Series: IP
- SubTypes: H-Frame Press
- Capacity Imperial Tons: 50
- Capacity KN: 498
- Quality welded frame for maximum strength and long life
- Exclusive Hydra-Lift bed for effortless adjustment of the vertical daylight (10-ton models are manual)
- Roller head design is standard to allow movement and locking of the cylinder from side to side(10-ton, 25-ton, and 30-ton are manual)
- All models in the Quick Selection Chart have been matched to a pump, cylinder, hoses and gauge, offering the complete package
- Set Includes: RR5013, ZE4420SB-N, GF50P, HC9306, GA2
- Accessories: PK501, A150, IPL100
50 Ton, H-Frame Hydraulic Press with RR5013 Double-Acting Cylinder, no pump and large pump mounting kit
EP IPH050D13-2
50 Ton, H-Frame Hydraulic Press with RR5013 Double-Acting Cylinder, no pump and large pump mounting kitH-Frame Presses (IP-Series)
- Type: Hydraulic Press
- Max PSI: 10000
- Product Group: Presses
- Series: IP
- SubTypes: H-Frame Press
- Capacity Imperial Tons: 50
- Set Includes: RR5013, GA2, GF50P, HC9306
54.9 ton Capacity, 3.94 in Stroke, Aluminum Lock Nut Hydraulic Cylinder
EP RACL504
54.9 ton Capacity, 3.94 in Stroke, Aluminum Lock Nut Hydraulic CylinderRACL-Series Aluminum Cylinders include a lock nut that gives the reassurance of safe mechanical load holding for extended periods. Each cylinder is single-acting with a high-strength return spring for rapid retraction. The integral stop ring prevents plunger over-travel. All are equipped with bolt-on hardened steel saddles and a steel base plate for increased durability.
Enerpac RACL Lock Nut Aluminum Hydraulic Cylinders can change the way you think about your cylinder applications. With approximately half of the weight of equivalent steel models, they combine an impressive power to weight ratio with the convenience of easier transport and positioning. RACL cylinders are rated for 10,000 psi (700 bar) and comply with ASME B30.1.
Aluminum is not only lightweight, but also inherently less corrosive than steel, which makes it a great material for use in many caustic environments. For enhanced protection, Enerpac RACL Aluminum Cylinders are finished with an anodized hard coat finish to resist damage and extend cylinder life.
Applications: Lift, Push, Hold
- Type: Hydraulic Cylinders
- Max Bar: 700
- Max PSI: 10000
- Product Group: Cylinders and Jacks
- Product Line: Industrial Tools
- Series: RACL
- Stroke Inches: 3.94
- Stroke MM: 100
- SubTypes: Aluminum Lock Nut Cylinder
- Aluminum Lock Nut provides mechanical load holding for extended periods
- Hardened steel stop ring increases cylinder life and resistance to side-loads of up to 5%
- Hard coat finish on all surfaces resists damage and extends cylinder life
- Composite bearings increase cylinder life and side load resistance
- Handles included on all models
- Steel base plate and saddle for protection against load-induced damage
- Integral stop ring prevents plunger over-travel and is capable of withstanding the full cylinder capacity
- High-strength return spring for rapid cylinder retraction
- CR400 coupler and dustcap included on all models
- All cylinders meet ASME B-30.1 standards
- Accessories: CATS50
55 Gallons, HF Hydraulic Oil for Powered Pumps
EP HF104
55 Gallons, HF Hydraulic Oil for Powered PumpsThe Enerpac HF-series Hydraulic Oil is specially formulated for powered hydraulic pumps. The HF-series oil contains anti-sludge, anti-rust, and anti-foam additives for overall superior performance. The HF-series hydraulic oil prevents cavitation and offers maximum volumetric efficiency and maximum heat transfer.
The HF-series oil is not for use in hand pumps. Use the Enerpac LX-Series Oil for hand powered pumps.
Offered in 1 quart, 1 gallon, 5 gallon and 55-gallon sizes. The HF-series hydraulic oil has a viscosity index of 100 min.
- Type: Hydraulic Oil
- Product Group: Pumps
- Product Line: Industrial Tools, Work Holding Tools, Bolting Tools
- Series: HF
- SubTypes: Oil
- Specially formulated for power pumps
- maximum volumetric efficiency
- maximum heat transfer
- prevents cavitation
- anti-sludge, anti-rust, anti-foam additives
- Maximum film protective lubricity
- anti-oxidation additives
- High viscosity index ensures maximum lubricity over a wide range of operation temperatures.
55 mm Socket for 1 in. Square Drive
EP BSH1055
55 mm Socket for 1 in. Square Drive- Type: Torque Wrench Accessory
- Product Group: Torque Wrenches, Torque Wrench Pumps
- Product Line: Bolting Tools
- Series: BSH
- SubTypes: Socket - Metric
55 Ton, 6.19 in Stroke, General Purpose Hydraulic Cylinder and Steel Hand Pump Set
EP ST556A
55 Ton, 6.19 in Stroke, General Purpose Hydraulic Cylinder and Steel Hand Pump SetGeneral Purpose Cylinder and Pump Set
- Type: Cylinder And PumpSet
- Max Bar: 700
- Max PSI: 10000
- Product Line: Hydraulic Tools
- Series: ST - Simplex
- Stroke Inches: 6.19
- Stroke MM: 157.2
- SubTypes: Steel General Purpose Cylinder and Steel Hand Pump Set
- Capacity Imperial Tons: 55
- Capacity KN: 489,3
- Set Includes: R556, P82, HCA6, GT25, GA1-Simplex
55, 4 mm Stroke, 50, 6 Kn Capacity, General Purpose Hydraulic Cylinder
EP BRW102
55,4 mm Stroke, 50,6 kN Capacity, General Purpose Hydraulic Cylinder- Type: Hydraulic Cylinders
- Max Bar: 700
- Max PSI: 10000
- Min Bar: 40
- Product Group: Cylinders and Jacks
- Product Line: Work Holding Tools
- Series: BRW
- Stroke MM: 55.4
- SubTypes: Workholding General Purpose Cylinder
- Single-acting heavy-duty cylinders handle a variety of applications
- High pressure (700 bar) design when additional force is required
- Long stroke lengths in compact design, well suited for welding applications
- Collar thread and base mounting holes allow flexible mounting options
- Hardened snap-in removable saddles for additional plunger protection
- Chrome plated plunger with bronze upper and lower bearing provide long life
55.2 ton Capacity, 10.25 in Stroke, General Purpose Hydraulic Cylinder
EP RC5010
55.2 ton Capacity, 10.25 in Stroke, General Purpose Hydraulic CylinderRC-TRIO is the next generation of the legendary Enerpac RC-Series single acting hydraulic cylinders. These hydraulic jacks include many advanced features to ensure superior durability, versatility, and productivity.
A pre-tensioned spring provides fast plunger retraction and enhanced productivity. The robust bearing system features composite wear bands and a hardened stop ring to resist side-load which minimizes damage and repairs. The plunger wiper, high-grade polyethylene seals and tough external finishes also help towards an extended service life.
With so many hydraulic cylinder models to choose from, we’re confident you’ll find the perfect match for your applications, and if you already own prior RC-Series cylinders, the good news is the new cylinders share the same familiar dimensions and threads for full compatibility.
Applications: Lift, Push
- Type: Hydraulic Cylinders
- Max Bar: 700
- Max PSI: 10000
- Product Group: Cylinders and Jacks
- Product Line: Industrial Tools
- Series: RC
- Stroke Inches: 10.25
- Stroke MM: 260
- SubTypes: General Purpose Cylinder
- Bearing system with composite wear bands for optimal sideload resistance
- Strengthened stop ring improves durability and side load resistance
- Trio Hybrid pre-tensioned spring system provides faster retraction
- High-grade polyethylene seals for low wear and long service life
- Plunger wiper reduces contamination, extending cylinder life.
- Collar and plunger threads and base mounting holes enable easy fixturing (on most models)
- Standard certified lifting eyes on cylinder models above 55 lbs. (25 kg) weight.
- Interchangeable with optional CHM6 carrying handle
- Designed for use in all positions
- Baked enamel finish for increased corrosion resistance
- Includes CR400 coupler, dust cap and collar thread protector
- RC-Series model numbers, external dimensions and threads remain unchanged from prior RC Series cylinders
- Spare Part(s): RC50044, HCL50045, RC5010040, RC50NK0, RC50NKS1, RC50NKS, RC50NKB1, RC50NKB2, RC50NKW
- Accessories: CATS100, JBI50, CHM6