GRACO INC. S10595

GG 287024

GUN, POLE, 6', DOMESTIC

Graco 287024 Pole Gun, 6 ft

Eliminate the hassles of ladders and scaffolding to safely spray hard-to-reach areas like high walls, vaulted ceilings, stairways, and soffits. Complete the job faster with less setup time with a pole gun.

• For unmatched spraying performance in high or recessed areas
• Provides better spray control and less fatigue
• Balanced design with no excessive weight at the end of the pole

• Model: Graco

• Bleed Type: Bleeder

• Compatible Material: Water-Based Paint

• Component A Inlet Size (in): 1/4
• Component Type: Single Component

• Fluid Orifice Size (cm): 0.229
• Fluid Orifice Size (in): 0.090
• Fluid Orifice Size (mm): 2.29

• For Use With: Electric Airless Sprayer

• Gun Activation: Manual
• Gun Type: Pole Gun
• Gun Weight (kg): 0.1589
• Gun Weight (lb): 3.5

• Includes: Cleanshot Shut-off Valve, Contractor In-line Valve

• Maximum Fluid Pressure (bar): 248
• Maximum Fluid Pressure (kPa): 24800
• Maximum Fluid Pressure (MPa): 24.8
• Maximum Fluid Pressure (psi): 3600

• Maximum Fluid Pressure (bar): 248
• Maximum Fluid Pressure (kPa): 24800
• Maximum Fluid Pressure (MPa): 24.8
• Maximum Fluid Pressure (psi): 3600

• Purge Method: Liquid

GG 286619

RAC 5 TIP, SPRAY

Graco 286619 RAC 5 SwitchTip, 619

The Reverse-A-Clean (RAC) 619 RAC 5 SwitchTip produces a 12 to 14 inch fan and has a 0.019 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Most Widely Used Reversible Spray Tip on the Market (Black Handle)

  Used for residential and commercial applications

  Includes OneSeal for most common coatings

  Large selection of tip sizes available

  Easy to identify laser stamped tip size

  Solvent seal available when using extremely hot solvents

• Model: RAC 5
• Series: SwitchTip

• Compatible Material: Latex Paint, Latex Stain, Oil-Based Paint, Oil-Based Stain

• For Use With: RAC 5 HandTite Tip Guard

• Maximum Fan Width (cm): 35.6
• Maximum Fan Width (in): 12
• Maximum Fan Width (mm): 356

• Maximum Flow Rate (GPM): 0.38
• Maximum Flow Rate (L/min): 1.44

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 12
• Minimum Fan Width (mm): 305

• Orifice Diameter (in): 0.019

GG 286721

RAC 5 TIP, SPRAY

Graco 286721 RAC 5 SwitchTip, 721

The Reverse-A-Clean (RAC) 721 RAC 5 SwitchTip produces a 14 to 16 inch fan and has a 0.021 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Most Widely Used Reversible Spray Tip on the Market (Black Handle)

  Used for residential and commercial applications

  Includes OneSeal for most common coatings

  Large selection of tip sizes available

  Easy to identify laser stamped tip size

  Solvent seal available when using extremely hot solvents

• Model: RAC 5
• Series: SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC 5 HandTite Tip Guard

• Maximum Fan Width (cm): 40.6
• Maximum Fan Width (in): 14
• Maximum Fan Width (mm): 406

• Maximum Flow Rate (GPM): 0.47
• Maximum Flow Rate (L/min): 1.78

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 14
• Minimum Fan Width (mm): 356

• Orifice Diameter (in): 0.021

• Pattern Size (in): 14 to 16
• Pattern Size (mm): 355.6 to 406.4

GG 287030

VALVE, SPRAY, PKG

Graco 287030 CleanShot Valve

Unique needle valve shuts fluid off at the tip for a clean pattern, no spitting. A great addition to any extension.

• Unique needle valve shuts fluid off at the tip for a clean pattern - no spitting
• 180 degree tip swivel provides versatility when spraying walls and ceilings
• Pressure-actuated - operates at a minimum of 700 psi (4.8 MPa, 48 bar)

• Model: CleanShot
• Series: CleanShot

• For Use With: JetRoller

• Includes: Gasket
• Inlet Size (cm): 0.635
• Inlet Size (in): 1/4
• Inlet Size (mm): 6.35

• Inlet Thread Type: NPSM

• Maximum Working Pressure (bar): 248
• Maximum Working Pressure (kPa): 24800
• Maximum Working Pressure (MPa): 24.8
• Maximum Working Pressure (psi): 3600

• Outlet Size (cm): 2.2225
• Outlet Size (in): 7/8
• Outlet Size (mm): 22.225
• Outlet Thread Type: UNF

GG 287033

KIT, FILTER, GUN, 100 MESH

Graco 287033 Gun Filter, 100 mesh

The Gun Filter helps reduce tip plugging and provides a better quality finish by eliminating unwanted particles from the spray pattern. Use 100 mesh for thinner materials such as stain and lacquer.

• The Gun Filter helps reduce tip plugging and provides a better quality finish by eliminating unwanted particles from the spray pattern
• Filters keep downtime to a minimum by reducing plugging at the spray tip
• Use 100 mesh for thinner materials such as stain and lacquer

• Model: Graco

• For Use With: Contractor PC Spray Gun, Contractor II Spray Gun, FTx Spray Gun

• Mesh Size: 100

• Number of Pieces: 1

• Overall Depth (cm): 0.9525
• Overall Depth (in): 0.375
• Overall Depth (mm): 9525

• Overall Height (cm): 10.16
• Overall Height (in): 4
• Overall Height (mm): 101.6
• Overall Width (cm): 0.9525
• Overall Width (in): 0.375
• Overall Width (mm): 9525

GG 287032

KIT, FILTER, GUN, 60 MESH

Graco 287032 Gun Filter, 60 mesh

The Gun Filter helps reduce tip plugging and provides a better quality finish by eliminating unwanted particles from the spray pattern. Use 60 mesh for materials such as primer and latex paint.

• The Gun Filter helps reduce tip plugging and provides a better quality finish by eliminating unwanted particles from the spray pattern
• Filters keep downtime to a minimum by reducing plugging at the spray tip
• Use 60 mesh for materials such as primer and latex paint.

• Model: Graco

• For Use With: Contractor PC Spray Gun, Contractor II Spray Gun, FTx Spray Gun

• Mesh Size: 60

• Number of Pieces: 1

• Overall Depth (cm): 0.9525
• Overall Depth (in): 0.375
• Overall Depth (mm): 9525

• Overall Height (cm): 10.16
• Overall Height (in): 4
• Overall Height (mm): 101.6
• Overall Width (cm): 0.9525
• Overall Width (in): 0.375
• Overall Width (mm): 9525

GG 287034

KIT, FILTER, GUN, 60/100MESH

Graco 287034 Gun Filters, (1) 60 mesh and (1) 100 mesh

The Gun Filter helps reduce tip plugging and provides a better quality finish by eliminating unwanted particles from the spray pattern. Use 60 mesh for materials such as primer and latex paint. Use 100 mesh for thinner materials such as stain and lacquer.

• Model: Graco

• For Use With: Contractor II Spray Gun, FTx Spray Gun

• Mesh Size: 60, 100

• Number of Pieces: 2

GG 287095

KIT, ACCESSORY, FLEX, 3/8, LTX

Graco 287095 Flex Plus Airless Spray Gun, RAC X, BlueMax II Airless Hose, 1/4 in x 50 ft, 3 ft Whip Hose

Get up and spraying quickly with the ideal spray gun for applications using heavy coatings and joint compounds along with needed accessories. Keep a spare kit on hand to always be prepared for large projects where dual gun applications are required.

• Flex Plus Airless Spray Gun
  

  Ergonomic handle

  No adjustment needle

  Patented needle design

  Large fluid path

• RAC X LTX 517 SwitchTip
  

  Provides 10 inch spray pattern

  Ideal for larger surfaces such as houses/buildings, walls and ceilings

  100% tested for flow rate

• BlueMax II Airless Hoses
  

  The lightest, most flexible hoses on the market

  Easy to connect and maintain

  The highest level of performance from the sprayer to the gun

• Model: Silver Gun

• Kit Type: Spray Gun and Hose Kit

GG 287222

VALVE, DISPENSE

Graco 287222 Air Actuated Fluid Valve

GG 287314

KIT REPAIR, HOSE, CPLD

Graco 287314 RotoFlex HD Pump Hose

• Model: Graco
• Series: RotoFlex HD

GG 287545

GG 287449

GG 287285

GG 287228

GG 287570

GG 287734

NEEDLE, ASSY

GG 287683

GG 287819

GG 287850

KIT, ACCY, SILVER PLUS GUN, GH83

Get up and spraying quickly with the industry's preferred spray gun for high-pressure applications and needed accessories. Keep a spare kit on hand to always be prepared for large projects where dual gun applications are required.

• Silver Plus Gun
  

  Lightweight, Rugged Design

  Exclusive Needle Design

  2-Finger Trigger Design and Handle

  Stainless Steel Fluid Tube

• RAC X LTX 517 & 655 SwitchTips
  

  Provides a 10 inch and 12 inch spray patterns

  Ideal for larger surfaces such as houses/buildings, walls and ceilings

  100% tested for flow rate

• BlueMax II Airless Hoses
  

  The lightest, most flexible hoses on the market

  Easy to connect and maintain

  The highest level of performance from the sprayer to the gun

• Model: Silver Plus

GG 286729

RAC 5 TIP, SPRAY

Graco 286729 RAC 5 SwitchTip, 729

The Reverse-A-Clean (RAC) 729 RAC 5 SwitchTip produces a 14 to 16 inch fan and has a 0.029 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Most Widely Used Reversible Spray Tip on the Market (Black Handle)

  Used for residential and commercial applications

  Includes OneSeal for most common coatings

  Large selection of tip sizes available

  Easy to identify laser stamped tip size

  Solvent seal available when using extremely hot solvents

• Model: RAC 5
• Series: SwitchTip

• Compatible Material: Lacquer to Mastic, Latex Paint

• For Use With: RAC 5 HandTite Tip Guard

• Maximum Fan Width (cm): 40.6
• Maximum Fan Width (in): 14
• Maximum Fan Width (mm): 406

• Maximum Flow Rate (GPM): 0.9
• Maximum Flow Rate (L/min): 3.41

• Maximum Working Pressure (bar): 280
• Maximum Working Pressure (kPa): 28000
• Maximum Working Pressure (psi): 4050

• Minimum Fan Width (in): 14
• Minimum Fan Width (mm): 356

• Orifice Diameter (in): 0.029

• Pattern Size (in): 14 to 16
• Pattern Size (mm): 355.6 to 406.4

GG 287902

GG 287915

GG 287976

KING SPRAYER, 40:1, D-ICE, HD, COMP, AA

Graco 287976 Heavy-Duty Cart Mounted AA Spray Package with 40:1 Mix Ratio and XL Air Motor with DataTrak

High-quality, high-volume, high-pressure. The Graco King pneumatic airless sprayers are the most powerful machines for protective coatings. The system provides the applicator output values, pressure ratios and pumping capacities never seen before. The Graco King units are designed to withstand the harshest environmental conditions and easily handle the toughest protective coatings and corrosion control applications. With 10 different ratios available, there is a sprayer with the correct pressure and flow characteristics for your application.

• Simple Maintenance
  

  This air motor has 50% less parts when compared to the NXT valve, making maintenance and troubleshooting easy.

  All motor parts are easily accessible and require simple maintenance

  • Improved Icing Performance

    The newly designed poppets and external pilot lines virtually eliminate pilot valve freezing that can result in an instant stop.

    The icing potential has been reduced by up to 70%

    • Less Pulsation

      With more than 145% higher exhaust capacity in the air valve, youll achieve a faster, smoother changeover.

      Eliminating the winkin your pattern - it is a difference you will feel.

      • New Air Motor

        Multi gun capabilities Graco's powerful new air motor lets you use multiple guns with almost no perceivable pulsation. A new manifold has been designed to simplify the installation of multiple guns.

        
        

        • Model: King
        • Air Inlet Size (in): 0.75
        • Air Inlet Thread Gender: Female
        • Air Inlet Thread Type: NPT
        • Approved for Hazardous Locations: Yes
        • Compatible Material: Protective Coating
        • Control Type: N/A
        • Convertible: Non-Convertible
        • Features: NXT Air Motor, DataTrak Control, Modular Air Valve, Quick Disconnect, Graco Xtreme Pump Lower with Built-In Filter
        • Fluid Inlet Size (in): 1-1/4
        • Fluid Inlet Size (mm): 31.75
        • Fluid Inlet Thread Gender: Male
        • Fluid Inlet Thread Type: NPT
        • Fluid Outlet Size (in): 1/2
        • Fluid Outlet Size (mm): 12.7
        • Fluid Outlet Thread Type: NPT
        • Frame Configuration: Heavy-Duty Cart
        • Gun Model: G40
        • Hose Inlet Diameter (cm):

GG 286635

RAC 5 TIP, SPRAY

Graco 286635 RAC 5 SwitchTip, 635

The Reverse-A-Clean (RAC) 635 RAC 5 SwitchTip produces a 12 to 14 inch fan and has a 0.035 inch orifice. Reverse the SwitchTip to easily clear clogs.

• Most Widely Used Reversible Spray Tip on the Market (Black Handle)

  Used for residential and commercial applications

  Includes OneSeal for most common coatings

  Large selection of tip sizes available

  Easy to identify laser stamped tip size

  Solvent seal available when using extremely hot solvents

  
  

  • Model: RAC 5
  • Series: SwitchTip
  • Compatible Material: Elastomer, Latex Paint, Latex Stain, Oil-Based Paint, Oil-Based Stain
  • For Use With: RAC 5 HandTite Tip Guard
  • Maximum Fan Width (cm): 35.6
  • Maximum Fan Width (in): 12
  • Maximum Fan Width (mm): 356
  • Maximum Flow Rate (GPM): 1.31
  • Maximum Flow Rate (L/min): 4.96
  • Maximum Working Pressure (bar): 280
  • Maximum Working Pressure (kPa): 28000
  • Maximum Working Pressure (psi): 4050
  • Minimum Fan Width (in): 12
  • Minimum Fan Width (mm): 305
  • Orifice Diameter (in): 0.035

GG 288046

GG 288053

GG 288171

KIT, REPAIR,AIR SEAL,LOW PSI

Graco 288171 Air Seal Repair Kit

GG 288160

MANIFOLD, REAR FITTING, INCH

Graco 288160 Rear port manifold, North America

GG 288117

REGULATOR, BACK PRESSURE

Graco 288117 Pneumatic Corrosion Resistant Fluid Back Pressure Regulator, 20 gpm, 300 psi max fluid pressure, 1-1/4 npt inlet/outlet, with gauge

• PTFE/Elastomer hybrid diaphragm withstands wear while maintaining accurate responsiveness
• Stainless steel wetted materials are compatible with catalyst and waterborne materials
• Hardened stainless steel seat ensure low wear and long life
• Air operated for remote automated control to eliminate operator interference

GG 288136

KIT, REPAIR,FLUID,AA

Graco 288136 Fluid Repair Kit for Automatic G40 Air-Assisted Spray Guns

GG 288191

KIT, NEEDLE ASSY, CARB/CARB

Graco 288191 Fluid Needle, carbide ball, standard viscosity/standard flow

GG 288184

GG 288190

KIT, NEEDLE ASSY (SST/DELRIN)

Graco 288190 Fluid Needle, SST ball, acid catalyzed materials/very low viscosity materials

GG 288196

KIT, DIFFUSER AIRLESS

Graco 288196 Ball Seat Diffuser- 3/16 in

GG 288194

KIT, AIRCAP ASSY, H.P.

Graco 288194 Standard Air Cap used with AAP, GG4, GG5, and AAM Series

• Compatible Material: Solvents, Paint, Coating, Lubrication-Fluid

GG 288192

KIT, DIFFUSER ASSY

Graco 288192 Diffuser-Seat, carbide seat, standard viscosity/standard flow

GG 288193

GG 288197

GG 288200

GG 288221

MANIFOLD, BOTTOM INLET (IN)

Graco 288221 Manifold with bottom fluid ports

GG 288224

MANIFOLD, ADJUSTABLE,DELTA,HIGH PRS

Graco 288224 High Pressure Air Assisted Manifold with side fluid ports and manual fan adjustment valve

GG 288048

AL AUTO GUN, AIRLESS AUTO

Graco 288048 AL Automatic Airless Spray Gun, includes GG0 spray tip of choice

A compact, lightweight automatic spray gun design that increases production speeds and provides a quality finish with a low cost of ownership.

• Lightweight and compact rounded gun design
• Capable of handling high production speeds
• Durable stainless steel construction handles the toughest materials
• Wide range tip line for a variety of applications

• Applicator Type: Automatic

• Bleed Type: Bleeder

• Gun Activation: Automatic
• Gun Included: 1
• Gun Type: Airless Gun
• Gun Weight (g): 529
• Gun Weight (kg): 0.544
• Gun Weight (lb): 1.17
• Gun Weight (oz): 19.2

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 360
• Maximum Fluid Pressure (kPa): 36000
• Maximum Fluid Pressure (MPa): 36
• Maximum Fluid Pressure (psi): 5000
• Maximum Fluid Temperature ( degree C): 60
• Maximum Fluid Temperature ( degree F): 140

• Maximum Fluid Pressure (bar): 360
• Maximum Fluid Pressure (kPa): 36000
• Maximum Fluid Pressure (MPa): 36
• Maximum Fluid Pressure (psi): 5000
• Maximum Fluid Temperature ( degree C): 60
• Maximum Fluid Temperature ( degree F): 140

• Product Type: Spray Gun

GG 288223

MANIFOLD, ADJUSTABLE,DELTA,LOW PRS

Graco 288223 North America Low Pressure Manifold with side fluid ports and fan adjustment valve

GG 288217

MANIFOLD, SIDE INLET (IN)

Graco 288217 North America Manifold with Side Fluid Ports

GG 288311

REGULATOR, BACK PRESSURE

Graco 288311 Pneumatic Back Pressure Regulator, 20 gpm (75 lpm), 300 psi (20.6 bar) max fluid pressure, 1-1/2 npt

• PTFE/Elastomer hybrid diaphragm withstands wear while maintaining accurate responsiveness
• Stainless steel wetted materials are compatible with catalyst and waterborne materials
• Hardened stainless steel seat ensure low wear and long life
• Air operated for remote automated control to eliminate operator interference

• Compatible Material: Catalyst, Waterborne

• Gauge Port Size (cm): 0.635
• Gauge Port Size (in): 1/4
• Gauge Port Size (mm): 6.35

• Gauge Port Type: NPT

• Includes: Gauge
• Inlet Size (cm): 3.81
• Inlet Size (in): 1-1/2
• Inlet Size (mm): 38.1

• Inlet Thread Type: NPT

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 70
• Maximum Air Inlet Pressure (psi): 100

• Maximum Flow Rate (GPM): 20
• Maximum Flow Rate (L/min): 75.7

• Maximum Regulated Pressure (bar): 17.2
• Maximum Regulated Pressure (kPa): 1720
• Maximum Regulated Pressure (psi): 250

• Maximum Viscosity (cP): 1000

• Maximum Working Pressure (bar): 21
• Maximum Working Pressure (kPa): 2100
• Maximum Working Pressure (psi): 300

• Minimum Regulated Pressure (bar): 1.7
• Minimum Regulated Pressure (kPa): 170
• Minimum Regulated Pressure (MPa): 0.017
• Minimum Regulated Pressure (psi): 25

• Outlet Size (cm): 3.81
• Outlet Size (in): 1-1/2
• Outlet Size (mm): 38.1
• Outlet Thread Type: NPT

GG 288185

KIT, PEEK NEEDLE TIP ,055

Graco 288185 Needle Tip Kit (5-pack, 4 grooves) for AirPro Guns with 0.047-0.070 in (1.2-1.8 mm) Nozzle

GG 288251

GG 288262

REGULATOR, BACK PRESSURE

Graco 288262 Pneumatic Back Pressure Regulator, 20 gpm (75 lpm), 300 psi (20.6 bar) max fluid pressure, 2 inch tri-clamp

• PTFE/Elastomer hybrid diaphragm withstands wear while maintaining accurate responsiveness
• Stainless steel wetted materials are compatible with catalyst and waterborne materials
• Hardened stainless steel seat ensure low wear and long life
• Air operated for remote automated control to eliminate operator interference

• Compatible Material: Catalyst, Waterborne

• Gauge Port Size (cm): 0.635
• Gauge Port Size (in): 1/4
• Gauge Port Size (mm): 6.35

• Gauge Port Type: NPT

• Includes: Gauge
• Inlet Size (cm): 5.08
• Inlet Size (in): 2
• Inlet Size (mm): 50.8

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 70
• Maximum Air Inlet Pressure (psi): 100

• Maximum Flow Rate (GPM): 20
• Maximum Flow Rate (L/min): 75.7

• Maximum Regulated Pressure (bar): 17.2
• Maximum Regulated Pressure (kPa): 1720
• Maximum Regulated Pressure (psi): 250

• Maximum Viscosity (cP): 1000

• Maximum Working Pressure (bar): 21
• Maximum Working Pressure (kPa): 2100
• Maximum Working Pressure (psi): 300

• Minimum Regulated Pressure (bar): 1.7
• Minimum Regulated Pressure (kPa): 170
• Minimum Regulated Pressure (MPa): 0.017
• Minimum Regulated Pressure (psi): 25

• Outlet Size (cm): 5.08
• Outlet Size (in): 2
• Outlet Size (mm): 50.8

GG 288420

CONTRACTOR GUN, RAC X(PKGD)

Graco 288420 Contractor Airless Spray Gun, 2 Finger Trigger, RAC X 517 SwitchTip

The Contractor Airless Spray Gun is the industry standard for performance and durability. Includes a 2-finger trigger and a RAC X 517 SwitchTip and Guard.

• Exclusive FlexSeal Needle
  • Totally enclosed patented design eliminates needle's exposure to fluid, extends needle life by 70%, and ensures consistent needle shut-off
  • Fluid pushes on seal to quickly shut off needle and reduce spitting
  • Spring is located outside fluid path for better flow
  • Helps eliminate pack out and slow needle shut-off
• Reduced Gun Spitting
  • Repositioned seat is closer to the tip, eliminating 60% of the dead space
  • Less paint left between needle and tip results in less spitting
• Ergonomic Design
  • Form-fitted handle provides maximum control and comfort
  • Detachable trigger guard swings clear of gun handle for easy filter access
  • Lightweight design reduces operator fatigue
• Modular Needle Design
  • Simply remove the trigger cross pin and unthread front housing to change out needle
• EasyGlide Swivel
  • Exclusive dual-seat swivel design reduces sealing friction under pressure, making this the best swivel on the market!
• Easy Out Gun Filter
  • Filters from the inside out to prevent filter from collapsing
  • Interchangeable with all Contractor series guns

• Model: Contractor
• Series: Airless Spray Gun

• Component A Inlet Thread Type: NPSM
• Component Type: Single Component

• Fluid Orifice Size (cm): 0.318
• Fluid Orifice Size (in): 0.125
• Fluid Orifice Size (mm): 3.17

• For Use With: Airless Sprayers

• Gun Activation: Manual
• Gun Type: Airless Gun
• Gun Weight (oz): 23.8

• Includes: RAC X 515 SwitchTip, RAC X HandTite Guard

• Maximum Fluid Pressure (bar): 248
• Maximum Fluid Pressure (kPa): 24800
• Maximum Fluid Pressure (MPa): 24.8
• Maximum Fluid Pressure (psi): 3600

• Maximum Fluid Pressure (bar): 248
• Maximum Fluid Pressure (kPa): 24800
• Maximum Fluid Pressure (MPa): 24.8
• Maximum Fluid Pressure (psi): 3600

GG 288421

CONTRACTOR GUN, RAC 5(PKGD)

Graco 288421 Contractor Airless Spray Gun, 2 Finger Trigger, RAC 5 517 SwitchTip

The Contractor Airless Spray Gun is the industry standard for performance and durability. Includes a 2-finger trigger and a RAC 5 517 SwitchTip and Guard.

• Exclusive FlexSeal Needle
  • Totally enclosed patented design eliminates needle's exposure to fluid, extends needle life by 70%, and ensures consistent needle shut-off
  • Fluid pushes on seal to quickly shut off needle and reduce spitting
  • Spring is located outside fluid path for better flow
  • Helps eliminate pack out and slow needle shut-off
• Reduced Gun Spitting
  • Repositioned seat is closer to the tip, eliminating 60% of the dead space
  • Less paint left between needle and tip results in less spitting
• Ergonomic Design
  • Form-fitted handle provides maximum control and comfort
  • Detachable trigger guard swings clear of gun handle for easy filter access
  • Lightweight design reduces operator fatigue
• Modular Needle Design
  • Simply remove the trigger cross pin and unthread front housing to change out needle
• EasyGlide Swivel
  • Exclusive dual-seat swivel design reduces sealing friction under pressure, making this the best swivel on the market!
• Easy Out Gun Filter
  • Filters from the inside out to prevent filter from collapsing
  • Interchangeable with all Contractor series guns

• Model: Contractor
• Series: Airless Spray Gun

• Component A Inlet Size (in): 1/4
• Component A Inlet Thread Type: NPSM

• Fluid Orifice Size (cm): 0.318
• Fluid Orifice Size (in): 0.125
• Fluid Orifice Size (mm): 3.17

• For Use With: Airless Sprayers

• Gun Activation: Manual
• Gun Type: Airless Gun
• Gun Weight (oz): 22

• Includes: RAC 5 517 SwitchTip, RAC 5 HandTite Guard

• Maximum Fluid Pressure (bar): 248
• Maximum Fluid Pressure (kPa): 24800
• Maximum Fluid Pressure (MPa): 24.8
• Maximum Fluid Pressure (psi): 3600

• Maximum Fluid Pressure (bar): 248
• Maximum Fluid Pressure (kPa): 24800
• Maximum Fluid Pressure (MPa): 24.8
• Maximum Fluid Pressure (psi): 3600

• Product Type: Spray Gun

GG 288429

FTX GUN, 2FINGER, RAC X 515, PKG

Graco 288429 Contractor FTx Airless Spray Gun, 2 Finger Trigger, RAC X 515 SwitchTip

The Contractor FTx Airless Spray Gun is the economical choice for everyday use while delivering the reliability and performance to achieve a professional finish. Includes a 2-finger trigger and a RAC X 515 SwitchTip and Guard.

• Exclusive FlexSeal Needle
  • Totally enclosed patented design eliminates needle's exposure to fluid, extends needle life by 70%, and ensures consistent needle shut-off
  • Fluid pushes on seal to quickly shut off needle and reduce spitting
  • Spring is located outside fluid path for better flow
  • Helps eliminate pack out and slow needle shut-off
• Reduced Gun Spitting
  • Repositioned seat is closer to the tip, eliminating 60% of the dead space
  • Less paint left between needle and tip results in less spitting
• Ergonomic Design
  • Form-fitted handle provides maximum control and comfort
  • Detachable trigger guard swings clear of gun handle for easy filter access
  • Lightweight design reduces operator fatigue
• Modular Needle Design
  • Simply remove the trigger cross pin and unthread front housing to change out needle
• EasyGlide Swivel
  • Exclusive dual-seat swivel design reduces sealing friction under pressure, making this the best swivel on the market!
• Easy Out Gun Filter
  • Filters from the inside out to prevent filter from collapsing
  • Interchangeable with all Contractor series guns

• Model: Contractor FTx
• Series: Airless Spray Gun

• Component A Inlet Size (in): 1/4
• Component A Inlet Thread Type: NPSM
• Component Type: Single Component

• Fluid Orifice Size (cm): 0.318
• Fluid Orifice Size (in): 0.125
• Fluid Orifice Size (mm): 3.17

• Gun Activation: Manual
• Gun Type: Airless Gun
• Gun Weight (oz): 23.8

• Includes: RAC X 515 SwitchTip, RAC X HandTite Guard

• Maximum Fluid Pressure (bar): 248
• Maximum Fluid Pressure (kPa): 24800
• Maximum Fluid Pressure (MPa): 24.8
• Maximum Fluid Pressure (psi): 3600

• Maximum Fluid Pressure (bar): 248
• Maximum Fluid Pressure (kPa): 24800
• Maximum Fluid Pressure (MPa): 24.8
• Maximum Fluid Pressure (psi): 3600

• Product Type: Spray Gun

GG 288431

FTX GUN, RAC 5(PKGD)

Graco 288431 Contractor FTx Airless Spray Gun, 4 Finger Trigger, RAC 5 515 SwitchTip

The Contractor FTx Airless Spray Gun is the economical choice for everyday use while delivering the reliability and performance to achieve a professional finish. Includes a 4-finger trigger and a RAC 5 515 SwitchTip and Guard.

• Exclusive FlexSeal Needle
  • Totally enclosed patented design eliminates needle's exposure to fluid, extends needle life by 70%, and ensures consistent needle shut-off
  • Fluid pushes on seal to quickly shut off needle and reduce spitting
  • Spring is located outside fluid path for better flow
  • Helps eliminate pack out and slow needle shut-off
• Reduced Gun Spitting
  • Repositioned seat is closer to the tip, eliminating 60% of the dead space
  • Less paint left between needle and tip results in less spitting
• Ergonomic Design
  • Form-fitted handle provides maximum control and comfort
  • Detachable trigger guard swings clear of gun handle for easy filter access
  • Lightweight design reduces operator fatigue
• Modular Needle Design
  • Simply remove the trigger cross pin and unthread front housing to change out needle
• EasyGlide Swivel
  • Exclusive dual-seat swivel design reduces sealing friction under pressure, making this the best swivel on the market!
• Easy Out Gun Filter
  • Filters from the inside out to prevent filter from collapsing
  • Interchangeable with all Contractor series guns

• Model: Contractor FTx
• Series: Airless Spray Gun

• Component A Inlet Size (in): 1/4
• Component A Inlet Thread Type: NPSM
• Component Type: Single Component

• Fluid Orifice Size (cm): 0.318
• Fluid Orifice Size (in): 0.125
• Fluid Orifice Size (mm): 3.17

• Gun Activation: Manual
• Gun Type: Airless Gun
• Gun Weight (oz): 23.8

• Includes: RAC 5 515 SwitchTip, RAC 5 HandTite Guard

• Maximum Fluid Pressure (bar): 248
• Maximum Fluid Pressure (kPa): 24800
• Maximum Fluid Pressure (MPa): 24.8
• Maximum Fluid Pressure (psi): 3600

• Maximum Fluid Pressure (bar): 248
• Maximum Fluid Pressure (kPa): 24800
• Maximum Fluid Pressure (MPa): 24.8
• Maximum Fluid Pressure (psi): 3600

• Product Type: Spray Gun

GG 288489

KIT, GUN/HOSE, CONT, RACX, 1/4 X

Graco 288489 Contractor Airless Spray Gun, RAC X, BlueMax II Airless Hose, 1/4 in x 50 ft, 3 ft Whip Hose

Get up and spraying quickly on everyday applications with industry-proven performance. Keep a spare kit on hand to always be prepared for large projects where dual gun applications are required.

• Contractor Airless Spray Gun

  The industry standard for performance and durability for over a decade

• RAC X LTX 517 SwitchTip

  Provides a 10 inch spray pattern

  Ideal for larger surfaces such as houses/buildings, walls and ceilings

  100% tested for flow rate

• BlueMax II Airless Hoses
  

  The lightest, most flexible hoses on the market

  Easy to connect and maintain

  The highest level of performance from the sprayer to the gun

• Model: Contractor
• Series: Airless Spray Gun

• Includes: Contractor II Spray Gun, RAC X 517 SwitchTip, 1/4 in x 50 ft BlueMax II Airless Hose, 3 ft BlueMax II Whip Hose

• Kit Type: Contractor Gun Kit

GG 288839

KIT, ACCESSORY,GUARD,RAC,AA

Graco 288839 AA RAC Guard for Flat Tip RAC Tip Air Cap Conversion Kit

GG 288887

GG 288897

GG 288749

KIT, FLTR, SG20/SG PRO, 60 MESH

Graco 288749 Gun Filter 60 mesh

Spray gun filters improve the look of the final finish by removing unwanted debris from the paint. 60 mesh filter is for material such as primer and latex paint.

• Gun filters help remove debris from the coating protecting the pump, reducing tip clogging and providing a better quality finish
• Replace the filter if clogged more than 20%
• Prolong pump life and reduce tip clogging by cleaning and replacing the filter regularly
• Clean after every use
• For use with Graco spray gun models SG10, SG20, SG Pro, SG2 and SG3

• Model: Graco
• Series: Gun Filter

• For Use With: SG2 Spray Gun, SG3 Spray Gun

• Mesh Size: 60

• Overall Depth (cm): 0.9525
• Overall Depth (in): 0.375
• Overall Depth (mm): 9.525

• Overall Height (cm): 10.16
• Overall Height (in): 4
• Overall Height (mm): 101.6
• Overall Width (cm): 0.9525
• Overall Width (in): 0.375
• Overall Width (mm): 9.525

GG 288863

GG 288810

GG 288501

KIT, GUN/HOSE, CONT, FF, 3/16 X 25'

Graco 288501 Contractor Airless Spray Gun, RAC X FF LP, BlueMax II Airless Hose, 3/16 in x 25 ft, 10 in Extension

Get up and spraying quickly on fine finish applications with industry-proven performance. Keep a spare kit on hand to always be prepared for large projects where dual gun applications are required.

• Contractor Airless Spray Gun

  The industry standard for performance and durability for over a decade

• RAC X FF LP 210 & 312 SwitchTips

  Provides the industry's best fine finish at the lowest airless spray pressure

  Reduced overspray

  Longer pump life

• BlueMax II Airless Hoses
  

  The lightest, most flexible hoses on the market

  Easy to connect and maintain

  The highest level of performance from the sprayer to the gun

• Model: Contractor
• Series: Airless Spray Gun

• Includes: Contractor II Spray Gun, RAC X FF LP 210, RAC X FF LP 312, 3/16 in x 25 ft BlueMax II Airless Hose, 10 in RAC X Tip Extension, (2) 100 Mesh Gun Filters, Solvent Seal Kit, Cleaning Brush

• Kit Type: Contractor Gun Kit

GG 288896

GG 288807

GG 288794

GG 288687

GG 288716

STRAINER, INLET, MAGNUM

Graco 288716 Inlet Strainer

Removes unwanted debris from the paint and reduces tip clogging. Clean and replace the inlet strainer regularly for long pump life and superior finish.

• Inlet strainer removes debris from the coating protecting the pump, reducing tip clogging and providing a better quality finish
• Prolong pump life and reduce tip clogging by cleaning and replacing the inlet strainer regularly
• Damaged or worn inlet strainers can let unwanted debris to enter into the pump

• Model: Graco
• Series: Inlet Strainer

• For Use With: Project Painter Plus, X5, X7, ProX17 Stand, ProX17 Cart, ProX19 Stand, ProX19 Cart, ProX21 Stand, ProX21 Cart, Magnum A20 Plus, Magnum A30 ProPlus, Magnum A45 ProPlus, Magnum A60 ProPlus, Magnum ProS19 ProPlus

• Overall Depth (cm): 4.445
• Overall Depth (in): 1.75
• Overall Depth (mm): 44.45

• Overall Height (cm): 5.08
• Overall Height (in): 2
• Overall Height (mm): 50.8
• Overall Width (cm): 4.445
• Overall Width (in): 1.75
• Overall Width (mm): 44.45

GG 288732

GG 288891

GG 288862

GG 288747

KIT, FLTR, PUMP, 40MESH, MAGNUM

Graco 288747 InstaClean Filter

Removes unwanted debris from the paint and reduces tip plugging to improve finish.

• Graco insta clean 40 mesh manifold filter provides extra filtration ensuring a better finish
• Form fitted one-way design prevents filter from being inserted incorrectly
• Filter automatically flushes clean when valve pressure is relieved

• Model: InstaClean
• Series: Filter

• For Use With: ProX17 Stand, ProX17 Cart, ProX19 Stand, ProX19 Cart, ProX21 Stand, ProX21 Cart, Magnum A60 ProPlus, Magnum A80 ProPlus, Magnum ProS19 ProPlus, Magnum ProS21 ProPlus

• Overall Depth (cm): 0.9525
• Overall Depth (in): 0.375
• Overall Depth (mm): 9.525

• Overall Height (cm): 4.7625
• Overall Height (in): 1.875
• Overall Height (mm): 47.625
• Overall Width (cm): 0.9525
• Overall Width (in): 0.375
• Overall Width (mm): 9.525

GG 288554

AUTOPLUS GUN, AIRLESS

Graco 288554 Automatic Airless Gun

Less maintenance and more system uptime

• Durable stainless steel construction, longer life needle and seat construction specifically designed to handle the toughest sealant and adhesive materials
• Lightweight and compact rounded gun design
• Capable of handling high production speeds
• Wide range tip line for a variety of applications
• Capable of handling multiple nozzle sizes for any application
• Lightweight and compact rounded gun design
• Capable of handling high production speeds
• Durable stainless steel construction handles the toughest materials
• Fewer parts means an overall lower cost of repair
• Capable of handling multiple nozzle sizes for any application

• Model: AutoPlus

• Application: Bonding, Sealing, Gasketing, Potting, Encapsulation, Spray, Metering, Regulating

• Connection Type: Threaded

• Flow Control Type: Control

• For Use With: PR70 Refill Kit

• Maximum Working Pressure (bar): 345
• Maximum Working Pressure (kPa): 34500
• Maximum Working Pressure (MPa): 35
• Maximum Working Pressure (psi): 5000

• Mount Location: Reciprocating Arm Rod Mount, Stationary Mount

• Number of Outputs: 1

GG 288817

KIT, REPAIR, GUN, SG20/SGPRO/SG2/SG3

Graco 288817 Gun Repair Kit for SG2, SG3, SG20, and SGPro Guns

The Graco gun repair kit will extend the life of your paint spray gun. Spray gun parts will wear with normal use from the abrasives used in coatings. Keep them in peak working order by replacing the worn parts.

• Repair kit is needed when the spray gun drips when trigger isnt pulled
• Replacing the worn parts will improve the fan pattern
• Gun repair kit is for SG2, SG20, SG3, SG Pro spray paint gun models

• For Use With: SG2, SG3, SG20, SGPro

GG 288858

KIT, REPAIR,AIR VALVE

Graco 288858 Air Valve Repair Kit for Fire-Ball, Monark, and President Air Motors

GG 288931

AIRPRO GUN,PRESSURE,AIR SPRAY,.055

Graco 288931 AirPro Air Spray Pressure Feed Gun, Conventional, 0.055 inch (1.4 mm) Nozzle, for General Metal Applications

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

GG 288935

AIRPRO GUN, PRESSURE, HVLP, .020

Graco 288935 AirPro Air Spray Pressure Feed Gun, HVLP, 0.020 inch (0.5 mm) Nozzle, for General Metal Applications

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: Metal
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: CARC, Enamel, Epoxies, Fast-Set, High Solids, Latex, Plural Component Materials, Sealants, Solvent borne, Urethane, Waterborne

• Component Type: Two Component

• Feed Type: Pressure Feed

• Fluid Orifice Size (cm): 0.051
• Fluid Orifice Size (in): 0.020
• Fluid Orifice Size (mm): 0.5

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: HVLP Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Minimum Flow Rate @ PSI (oz/min): 4

• Product Type: Spray Gun

GG 288942

AIRPRO GUN, PRESSURE, COMPLIANT, .020

Graco 288942 AirPro Air Spray Pressure Feed Gun, Compliant, 0.020 inch (0.5 mm) Nozzle, for General Metal Applications

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: Metal
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: CARC, Enamel, Epoxies, Fast-Set, High Solids, Latex, Plural Component Materials, Sealants, Solvent borne, Urethane, Waterborne

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 0.9525
• Fluid Inlet Size (in): 3/8
• Fluid Inlet Size (mm): 9.525
• Fluid Inlet Thread Type: NPSM
• Fluid Orifice Size (cm): 0.05
• Fluid Orifice Size (in): 0.020
• Fluid Orifice Size (mm): 0.5

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: Compliant Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Minimum Flow Rate @ PSI (oz/min): 4

• Product Type: Spray Gun

GG 288943

AIRPRO GUN, PRESSURE, COMPLIANT, .030

Graco 288943 AirPro Air Spray Pressure Feed Gun, Compliant, 0.030 inch (0.8 mm) Nozzle, for General Metal Applications

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: Metal
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: CARC, Enamel, Epoxies, Fast-Set, High Solids, Latex, Plural Component Materials, Sealants, Solvent borne, Urethane, Waterborne

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 0.9525
• Fluid Inlet Size (in): 3/8
• Fluid Inlet Size (mm): 9.525
• Fluid Inlet Thread Type: NPSM
• Fluid Orifice Size (cm): 0.08
• Fluid Orifice Size (in): 0.030
• Fluid Orifice Size (mm): 0.8

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: Compliant Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Product Type: Spray Gun

GG 288949

AIRPRO GUN, SST TIP, AIR SPRAY, .042

Graco 288949 AirPro Air Spray Pressure Feed Gun, Conventional, 0.042 inch (1.1 mm) Nozzle, SST Tip, for General Metal Applications

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: Metal
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: CARC, Enamel, Epoxies, Fast-Set, High Solids, Latex, Plural Component Materials, Sealants, Solvent borne, Urethane, Waterborne

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 0.9525
• Fluid Inlet Size (in): 3/8
• Fluid Inlet Size (mm): 9.525
• Fluid Inlet Thread Type: NPSM
• Fluid Orifice Size (cm): 0.11
• Fluid Orifice Size (in): 0.042
• Fluid Orifice Size (mm): 1.1

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: Conventional Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Product Type: Spray Gun

GG 288488

GG 288955

AIRPRO GUN, SST TIP, COMPLIANT, .042

Graco 288955 AirPro Air Spray Pressure Feed Gun, Compliant, 0.042 inch (1.1 mm) Nozzle, SST Tip, for General Metal Applications

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: Metal
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: CARC, Enamel, Epoxies, Fast-Set, High Solids, Latex, Plural Component Materials, Sealants, Solvent borne, Urethane, Waterborne

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 0.9525
• Fluid Inlet Size (in): 3/8
• Fluid Inlet Size (mm): 9.525
• Fluid Inlet Thread Type: NPSM
• Fluid Orifice Size (cm): 0.11
• Fluid Orifice Size (in): 0.042
• Fluid Orifice Size (mm): 1.1

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: Compliant Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Product Type: Spray Gun

GG 288964

AIRPRO GUN, WB, AIR SPRAY, .030

Graco 288964 AirPro Air Spray Pressure Feed Gun, Conventional, 0.030 inch (0.8 mm) Nozzle, for Waterborne Applications

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: Waterborne
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: Enamel, Epoxies, High Solids, Latex, Lacquer, Plural Component Materials, Sealants, Urethane, UV Coating, Waterborne

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 0.9525
• Fluid Inlet Size (in): 3/8
• Fluid Inlet Size (mm): 9.525
• Fluid Inlet Thread Type: NPSM
• Fluid Orifice Size (cm): 0.08
• Fluid Orifice Size (in): 0.030
• Fluid Orifice Size (mm): 0.8

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: Conventional Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Product Type: Spray Gun

GG 288968

AIRPRO GUN, WB, HVLP, .042

Graco 288968 AirPro Air Spray Pressure Feed Gun, HVLP, 0.042 inch (1.1 mm) Nozzle, for Waterborne Applications

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: Waterborne
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: Enamel, Epoxies, High Solids, Latex, Lacquer, Plural Component Materials, Sealants, Urethane, UV Coating, Waterborne

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 0.9525
• Fluid Inlet Size (in): 3/8
• Fluid Inlet Size (mm): 9.525
• Fluid Inlet Thread Type: NPSM
• Fluid Orifice Size (cm): 0.11
• Fluid Orifice Size (in): 0.042
• Fluid Orifice Size (mm): 1.1

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: HVLP Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Product Type: Spray Gun

GG 288969

AIRPRO GUN, WB, HVLP, .055

Graco 288969 AirPro Air Spray Pressure Feed Gun, HVLP, 0.055 inch (1.4 mm) Nozzle, for Waterborne Applications

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: Waterborne
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: Enamel, Epoxies, High Solids, Latex, Lacquer, Plural Component Materials, Sealants, Urethane, UV Coating, Waterborne

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 0.9525
• Fluid Inlet Size (in): 3/8
• Fluid Inlet Size (mm): 9.525
• Fluid Inlet Thread Type: NPSM
• Fluid Orifice Size (cm): 0.14
• Fluid Orifice Size (in): 0.055
• Fluid Orifice Size (mm): 1.4

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: HVLP Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Product Type: Spray Gun

GG 288971

AIRPRO GUN, WB, COMPLIANT, .042

Graco 288971 AirPro Air Spray Pressure Feed Gun, Compliant, 0.042 inch (1.1 mm) Nozzle, for Waterborne Applications

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: Waterborne
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: Enamel, Epoxies, High Solids, Latex, Lacquer, Plural Component Materials, Sealants, Urethane, UV Coating, Waterborne

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 0.9525
• Fluid Inlet Size (in): 3/8
• Fluid Inlet Size (mm): 9.525
• Fluid Inlet Thread Type: NPSM
• Fluid Orifice Size (cm): 0.11
• Fluid Orifice Size (in): 0.042
• Fluid Orifice Size (mm): 1.1

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: Compliant Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Product Type: Spray Gun

GG 288972

AIRPRO GUN, WB, COMPLIANT, .055

Graco 288972 AirPro Air Spray Pressure Feed Gun, Compliant, 0.055 inch (1.4 mm) Nozzle, for Waterborne Applications

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: Waterborne
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: Enamel, Epoxies, High Solids, Latex, Lacquer, Plural Component Materials, Sealants, Urethane, UV Coating, Waterborne

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 0.9525
• Fluid Inlet Size (in): 3/8
• Fluid Inlet Size (mm): 9.525
• Fluid Inlet Thread Type: NPSM
• Fluid Orifice Size (cm): 0.14
• Fluid Orifice Size (in): 0.055
• Fluid Orifice Size (mm): 1.4

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: Compliant Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Product Type: Spray Gun

GG 288976

AIRPRO GUN, CERAMIC, HVLP, .059

Graco 288976 AirPro Air Spray Pressure Feed Gun, HVLP, 0.059 inch (1.5 mm) Nozzle, for High Wear Applications

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: High Wear
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: Ceramics, Enamel, High Solids, Metallics, Solvent borne, Waterborne

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 0.9525
• Fluid Inlet Size (in): 3/8
• Fluid Inlet Size (mm): 9.525
• Fluid Inlet Thread Type: NPSM
• Fluid Orifice Size (cm): 0.15
• Fluid Orifice Size (in): 0.059
• Fluid Orifice Size (mm): 1.5

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: HVLP Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Product Type: Spray Gun

GG 288984

GG 289003

AIRPRO GUN, CONV, .070

Graco 289003 AirPro Air Spray Gravity Feed Gun, Conventional, 0.070 inch (1.8 mm) Nozzle, without Cup

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: Specialty
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: CARC, Enamel, Epoxies, Fast-Set, High Solids, Latex, Plural Component Materials, Sealants, Solvent borne, Urethane, Waterborne

• Feed Type: Gravity Feed

• Fluid Inlet Size (cm): 0.9525
• Fluid Inlet Size (in): 3/8
• Fluid Inlet Size (mm): 9.525
• Fluid Inlet Thread Type: NPSM
• Fluid Orifice Size (cm): 0.18
• Fluid Orifice Size (in): 0.070
• Fluid Orifice Size (mm): 1.8

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: Conventional Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Product Type: Spray Gun

GG 288985

AIRPRO GUN, SPATTER, HVLP, .042

Graco 288985 AirPro Air Spray Pressure Feed Gun, HVLP, 0.042 inch (1.1 mm) Nozzle, Spatter Applications

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: Spatter
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: Latex, Solvent borne, Spatter, Urethane, Waterborne

• Feed Type: Pressure Feed

• Fluid Inlet Size (cm): 0.9525
• Fluid Inlet Size (in): 3/8
• Fluid Inlet Size (mm): 9.525
• Fluid Inlet Thread Type: NPSM
• Fluid Orifice Size (cm): 0.11
• Fluid Orifice Size (in): 0.042
• Fluid Orifice Size (mm): 1.1

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: HVLP Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Product Type: Spray Gun

GG 289005

AIRPRO GUN, HVLP, .055

Graco 289005 AirPro Air Spray Gravity Feed Gun, HVLP, 0.055 inch (1.4 mm) Nozzle, without Cup

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: Specialty
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: CARC, Enamel, Epoxies, Fast-Set, High Solids, Latex, Plural Component Materials, Sealants, Solvent borne, Urethane, Waterborne

• Feed Type: Gravity Feed

• Fluid Inlet Size (cm): 0.9525
• Fluid Inlet Size (in): 3/8
• Fluid Inlet Size (mm): 9.525
• Fluid Inlet Thread Type: NPSM
• Fluid Orifice Size (cm): 0.14
• Fluid Orifice Size (in): 0.055
• Fluid Orifice Size (mm): 1.4

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: HVLP Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Product Type: Spray Gun

GG 289002

AIRPRO GUN, CONV, .055

Graco 289002 AirPro Air Spray Gravity Feed Gun, Conventional, 0.055 inch (1.4 mm) Nozzle, without Cup

The AirPro air spray gun delivers exceptional spray performance while addressing your environmental and operator concerns - whether you're a custom shop or a high volume manufacturing facility.

• Even material distribution through the spray pattern for optimum coverage
• Improved transfer efficiency through reduced air consumption
• Enhanced atomization through material-specific aircaps
• Ultra-light trigger pull reduces operator muscle stress
• Ergonomic gun handle provides a comfortable grip
• Rounded control knobs for operator comfort
• Optimize spray performance with our cutting edge aircap and nozzle design
• Choose from a wide range of gun models to meet the needs of your specific application

• Model: AirPro

• Air Inlet Size (cm): 0.635
• Air Inlet Size (in): 1/4
• Air Inlet Size (mm): 6.35
• Air Inlet Thread Type: NPSM

• Application: Specialty
• Applicator Type: Manual

• Bleed Type: Non-Bleeder

• Compatible Material: CARC, Enamel, Epoxies, Fast-Set, High Solids, Latex, Plural Component Materials, Sealants, Solvent borne, Urethane, Waterborne

• Feed Type: Gravity Feed

• Fluid Inlet Size (cm): 0.9525
• Fluid Inlet Size (in): 3/8
• Fluid Inlet Size (mm): 9.525
• Fluid Inlet Thread Type: NPSM
• Fluid Orifice Size (cm): 0.14
• Fluid Orifice Size (in): 0.055
• Fluid Orifice Size (mm): 1.4

• Gun Activation: Manual
• Gun Included: 1
• Gun Type: Conventional Gun
• Gun Weight (g): 410

• Includes: Air Cap, Needle Assembly, Nozzle, Tool Kit

• Maximum Air Inlet Pressure (bar): 7
• Maximum Air Inlet Pressure (kPa): 700
• Maximum Air Inlet Pressure (MPa): 0.7
• Maximum Air Inlet Pressure (psi): 100
• Maximum Air Pressure (bar): 7

• Maximum Air Pressure (kPa): 700
• Maximum Air Pressure (MPa): 0.7
• Maximum Air Pressure (psi): 100

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Maximum Fluid Pressure (bar): 21
• Maximum Fluid Pressure (kPa): 2100
• Maximum Fluid Pressure (MPa): 2.1
• Maximum Fluid Pressure (psi): 300
• Maximum Fluid Temperature ( degree C): 43
• Maximum Fluid Temperature ( degree F): 109

• Product Type: Spray Gun